HDS/TS68

Subcategories

• HDS68 Bille 8mm

  8 mm slugs caliber .68 for HDS68 and TS68

  8 mm slugs for Umarex T4E HDS68 and TS68 launchers, designed for recreational target shooting. Caliber .68 projectiles offering consistent shooting behavior and a good accuracy/impact ratio.

  Features

  • Type: slugs (balls) caliber .68
  • Diameter: 8 mm
  • Use: recreational target shooting
  • Consistent behavior from one shot to the next
  • Good accuracy / impact ratio
  • Made in France

  Why this 8 mm caliber

  The 8 mm diameter is designed to fit the cylinder and barrel of the HDS68 and TS68. This sizing ensures consistent placement of the projectiles, which translates into a steady trajectory and tighter groupings on target. Where poorly calibrated projectiles generate shooting discrepancies, these slugs aim for homogeneous behavior, session after session.

  Compatibility

  • Umarex T4E HDS68
  • Umarex T4E TS68

  These slugs are designed for the caliber .68 launchers mentioned above. Use on other .68 models remains possible but has not been tested by us.

  Use

  Reserved for recreational target shooting, on private land. Insert the projectiles into the cylinder or magazine intended for caliber .68 depending on your launcher, then shoot as with your usual ammunition. For consistent operation, make sure to use clean projectiles free of deformation.

  The Invent3D expertise

  Like all of our products, these slugs are part of a French and artisanal manufacturing approach. Invent3D designs accessories and projectiles dedicated to category D compressed-air weapons (less than 20 joules), for legal recreational use. A human and responsive customer service remains at your disposal for any question about compatibility or use.

  Delivery

  Fast and careful shipping from France 📦.

• HDS68 Bille 10mm

  Slugs 10 mm calibre .68 pour HDS68 et TS68

  Slugs de 10 mm calibre .68 conçus pour le tir de loisir sur cible avec les lanceurs Umarex T4E HDS68 et TS68. Impact franc et trajectoire régulière à chaque tir, pour des sessions plus précises.

  Caractéristiques

  • Calibre : .68
  • Diamètre : 10 mm
  • Type : slug pour tir de loisir sur cible
  • Fabrication française en impression 3D
  • Exclusivité Invent3D — copie interdite

  Pourquoi choisir ces slugs

  Le diamètre de 10 mm assure un bon positionnement dans le barillet et une mise en mouvement nette du projectile : c'est ce qui donne cet impact franc sur la cible. La géométrie du slug favorise une trajectoire régulière, pour un groupement plus constant tir après tir lors de vos sessions sur terrain privé sécurisé. C'est le projectile pensé pour qui cherche de la régularité et un comportement prévisible d'un tir à l'autre.

  Fabriqués en France en impression 3D, ces slugs sont pensés dès le départ pour l'usage loisir sur les lanceurs T4E de catégorie D (moins de 20 joules), en vente libre aux personnes majeures. Cette maîtrise de la fabrication assure une régularité d'un lot à l'autre, là où de nombreux projectiles du commerce restent génériques. Une exclusivité Invent3D, produite dans notre atelier français.

  Compatibilité

  • Umarex T4E HDS68
  • Umarex T4E TS68

  Ces slugs 10 mm sont étudiés pour les lanceurs Umarex T4E HDS68 et TS68. Ils peuvent convenir à d'autres modèles calibre .68 acceptant un projectile de ce diamètre, mais cette utilisation n'a pas été testée par nos soins. En cas de doute, notre service client reste à votre disposition pour vous orienter.

  Utilisation

  Réservés au tir de loisir sur cible. Chargez le slug dans le barillet ou le chargeur de votre HDS68 ou TS68 selon le modèle. Vérifiez toujours le bon positionnement du projectile avant le tir.

  Made in France

  Conçus et fabriqués en France en impression 3D, ces slugs sont une exclusivité Invent3D. Conception et production maîtrisées, pour des projectiles dédiés au tir de loisir avec vos lanceurs Umarex T4E. 🇫🇷

  Livraison

  Vos slugs 10 mm sont expédiés rapidement et soigneusement emballés depuis la France. 📦

• HDS68 Bille 12mm

  12 mm .68 Caliber Slugs for HDS68 and TS68

  12 mm ball slugs in .68 caliber, designed for the Umarex T4E HDS68 and TS68 launchers. Maximum mass for a powerful impact on target, in recreational shooting on secure private property.

  Specifications

  • Caliber: .68
  • 12 mm ball
  • Maximum mass for the caliber, ensuring a powerful impact on target
  • Use: recreational target shooting
  • French manufacturing, 3D printed

  Why choose these slugs

  The high mass of these 12 mm balls gives them significant kinetic energy on impact. In concrete terms, this translates into a more pronounced strike on the target, which appeals to shooters looking for sensation and power during their recreational shooting sessions. These projectiles offer the best weight-to-caliber balance for those seeking maximum energy on impact, shot after shot.

  The .68 caliber is the standard for the HDS68 and TS68 launchers: these slugs are sized to fit these models and deliver consistent behavior when firing. Made in France by Invent3D, they are aimed at connoisseurs who want to optimize their shooting sessions as well as beginners looking for reliable, high-performing ammunition. This control over manufacturing ensures consistency from one batch to the next.

  Compatibility

  • Umarex T4E HDS68
  • Umarex T4E TS68
  • Any T4E launcher in .68 caliber that accepts 12 mm balls

  For another model not listed above, please check the caliber and the ball diameter accepted before purchase. If you have any doubt about compatibility with your equipment, our customer service is available to help.

  Made in France

  Designed and made in France by Invent3D, these slugs are designed for recreational shooting. Designed and produced in-house, for projectiles dedicated to your Umarex T4E .68 caliber launchers. 🇫🇷

  Shipping

  Your 12 mm slugs are shipped quickly and carefully packaged from France. 📦

• HDS68 Bille 13,5mm

  13.5 mm slugs .68 caliber for HDS68 and TS68

  3D printed 13.5 mm slugs for Umarex T4E HDS68 and TS68 launchers. These are the largest balls in our .68 caliber range, designed to offer maximum mass and powerful impact on target during recreational shooting.

  Features

  • Diameter: 13.5 mm
  • Caliber: .68
  • Design: the largest ball in our .68 caliber range
  • Maximum mass for a powerful impact on target
  • French manufacturing with 3D printing

  Why choose these 13.5 mm slugs

  The 13.5 mm diameter represents the top of our .68 caliber range: it is the most voluminous ball we offer. This maximum mass translates directly into a more pronounced impact on the target, an argument appreciated by shooters looking for the most powerful in this category for their recreational shooting sessions.

  Designed and 3D printed in France, these slugs are part of a logic of careful, artisanal manufacturing. You benefit from a product designed specifically for your T4E launchers, where many commercial projectiles remain generic.

  Compatibility

  • Umarex T4E HDS68
  • Umarex T4E TS68

  These 13.5 mm slugs are designed for the .68 caliber of these two models. For any other launcher, check the compatibility of the caliber and diameter beforehand before use.

  Made in France

  Manufactured in France with 3D printing, these slugs are part of our exclusive .68 caliber range. Design and production mastered by Invent3D, for an accessory dedicated to recreational shooting with your Umarex T4E launchers.

  Delivery

  Your 13.5 mm slugs are shipped quickly and carefully packaged.

• Accessories

  3D Printed Accessories for HDS68 and TS68

  Customization and upgrade parts for Umarex T4E .68 caliber launchers. Designed and manufactured in France, these accessories install easily, without any permanent modification to your equipment.

  Features

  • Category: accessories for HDS68 / TS68
  • Caliber concerned: .68
  • Function: customization and upgrade parts
  • Manufacturing: 3D printing, Made in France
  • Simple mounting, without permanent modification of the equipment

  Compatibility

  These accessories are designed for the Umarex T4E .68 caliber launchers of the HDS68 and TS68 models. The caliber and dimensions are designed for these platforms: you mount the part directly, without permanent intervention on the firearm.

  Why choose these Invent3D accessories

  Do you own an HDS68 or a TS68 and want to upgrade it? This range is made for that. Each part is designed and manufactured in France using 3D printing, which makes it possible to obtain accessories precisely adapted to these models.

  • Customization: adapt the appearance and ergonomics of your launcher according to your preferences.
  • Upgrade: evolve your equipment for recreational shooting on private property.
  • Simple mounting: installation within everyone's reach, beginners as well as experts.
  • Without permanent modification: you keep your equipment intact and reversible.
  • French manufacturing: artisanal quality and a human and responsive customer service.

  Mounting

  The installation is designed to remain simple and reversible. The accessories mount onto the HDS68 or the TS68 without any special tooling or permanent transformation, which allows you to return to the original configuration at any time.

  Made in France

  All our accessories are designed and 3D printed in France. This artisanal manufacturing allows us to offer parts dedicated to the HDS68 and TS68 models, within the framework of category D recreational shooting, fully legally for adults.

  Delivery

  Your accessories are shipped carefully packaged.